SSC/Structure/BiPolytropes/51RenormaizePart2: Difference between revisions
| Line 613: | Line 613: | ||
\biggr] | \biggr] | ||
\biggr\}^{-1} | \biggr\}^{-1} | ||
</math> | |||
</td> | |||
</tr> | |||
<tr> | |||
<td align="right"> | |||
| |||
</td> | |||
<td align="center"><math>=</math></td> | |||
<td align="left"> | |||
<math>(2\pi)^{1/2} \mathcal{m}_\mathrm{surf}^7 \biggl(\frac{\mu_e}{\mu_c}\biggr)^{-12} \theta^{7}_i | |||
\cdot \frac{A}{\eta^4} | |||
\cdot | |||
\biggl[ \eta\cos(\eta-B) - \sin(\eta-B) \biggr] \, . | |||
</math> | </math> | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
<font color="red">Correct!</font> | |||
==Example Models Along BiPolytrope Sequence 0.3100== | ==Example Models Along BiPolytrope Sequence 0.3100== | ||
Revision as of 15:19, 19 August 2022
Radial Oscillations in (nc,ne) = (5,1) Bipolytropes
Logically, this chapter extends the discussion — specifically the subsection titled, Try Again — found in the "Ramblings" chapter in which we introduced a total-mass-based renormalization of models along sequences of bipolytropes.
Building Each Model
Basic Equilibrium Structure
Most of the details underpinning the following summary relations can be found here.
|
Quantity |
|
|
|||||||||||||||||||||||||||
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|||||||||||||||||||||||||||
|
|
|
|
|||||||||||||||||||||||||||
|
Note that, for a given specification of the molecular-weight ratio, , and the interface location, , in which case,
|
|||||||||||||||||||||||||||||
Additional Relations
Core
The analytically prescribed radial pressure gradient in the core can be obtained as follows.
|
|
||
|
|
||
|
|
||
|
|
Also,
|
|
Hence,
|
|
||
|
|
For comparison, in hydrostatic balance we expect …
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This matches our earlier expression, as it should.
|
Takeaway Expression
|
Envelope
Given that, for the envelope,
|
|
and, |
|
|
|
|
we deduce that,
|
|
|
|
|
|
|
|
|
|
|
As a cross-check …
|
|
|
|
|
|
|
and,
|
|
|
|
|
|
|
That is,
|
|
|
|
|
|
|
Correct!
Example Models Along BiPolytrope Sequence 0.3100
For the case of and , we consider here the examination of models with three relatively significant values of the core/envelope interface:
- Model D : Approximate location along the sequence of the model with the maximum fractional core radius.
- Model C : Approximate location along the sequence of the onset of fundamental-mode instability.
- Model A : Exact location along the sequence of the model with the maximum fractional core mass.
Model C
Here we examine a discrete representation of a model along the sequence whose core/envelope interface is located a .
See Also
|
Appendices: | VisTrailsEquations | VisTrailsVariables | References | Ramblings | VisTrailsImages | myphys.lsu | ADS | |