SSC/Structure/BiPolytropes/51RenormaizePart2: Difference between revisions
| Line 154: | Line 154: | ||
<td align="left"><math> | <td align="left"><math> | ||
\eta_i\biggl(1 + \Lambda_i^2\biggr)^{1 / 2} \, ,</math></td> | \eta_i\biggl(1 + \Lambda_i^2\biggr)^{1 / 2} \, ,</math></td> | ||
</tr> | |||
<tr> | |||
<td align="right"><math>B</math></td> | |||
<td align="center"><math>=</math></td> | |||
<td align="left"><math> | |||
\eta_i - \frac{\pi}{2} + \tan^{-1}(\Lambda_i) \, ,</math></td> | |||
</tr> | </tr> | ||
| Line 159: | Line 166: | ||
<td align="right"><math>\eta_s</math></td> | <td align="right"><math>\eta_s</math></td> | ||
<td align="center"><math>=</math></td> | <td align="center"><math>=</math></td> | ||
<td align="left"><math> | <td align="left"><math>\pi + B = | ||
\frac{\pi}{2} + \eta_i + \tan^{-1}(\Lambda_i) \, ,</math></td> | \frac{\pi}{2} + \eta_i + \tan^{-1}(\Lambda_i) \, ,</math></td> | ||
</tr> | </tr> | ||
Revision as of 14:40, 20 August 2022
Radial Oscillations in (nc,ne) = (5,1) Bipolytropes
Logically, this chapter extends the discussion — specifically the subsection titled, Try Again — found in the "Ramblings" chapter in which we introduced a total-mass-based renormalization of models along sequences of bipolytropes.
Building Each Model
Basic Equilibrium Structure
Most of the details underpinning the following summary relations can be found here.
Note: For an n = 5 polytrope (like our bipolytrope's core), the units of the polytropic constant, , are .
|
Quantity |
|
|
||||||||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||||||||
|
Note that, for a given specification of the molecular-weight ratio, , and the interface location, , in which case,
|
||||||||||||||||||||||||||||||||
Additional Relations
Core
The analytically prescribed radial pressure gradient in the core can be obtained as follows.
|
|
||
|
|
||
|
|
||
|
|
Also,
|
|
Hence,
|
|
||
|
|
For comparison, in hydrostatic balance we expect …
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This matches our earlier expression, as it should.
|
Takeaway Expression
|
Envelope
Given that, for the envelope,
|
|
and, |
|
|
|
|
we deduce that,
|
|
|
|
|
|
|
|
|
|
|
As a cross-check …
|
|
|
|
|
|
|
and,
|
|
|
|
|
|
|
That is,
|
|
|
|
|
|
|
Correct!
Time-Dependent Euler Equation
We begin with the form of the,
Euler Equation
that is broadly relevant to studies of radial oscillations in spherically symmetric configurations. Recognizing from, for example, a related discussion that, , and that,
we obtain our
|
Desired Form of the Euler Equation |
||
Given as well that,
we see that,
Next, if as above, we multiply through by , we obtain the relevant,
|
Normalized Euler Equation |
||
where, as a reminder, the dimensionless time is,
Finite-Difference Representation of Equilibrium State
STEP1: Divide the core into grid lines — that is, into radial zones — associating the first "grid line" with the center of the core and the last grid line with the radial location of the core/envelope interface. Choosing as the principal Lagrangian coordinate, and using the available analytic expressions, assign values to the following physical quantities at each grid line:
- Mass: Set ; then, for , set
Example Models Along BiPolytrope Sequence 0.3100
For the case of and , we consider here the examination of models with three relatively significant values of the core/envelope interface:
- Model D : Approximate location along the sequence of the model with the maximum fractional core radius.
- Model C : Approximate location along the sequence of the onset of fundamental-mode instability.
- Model A : Exact location along the sequence of the model with the maximum fractional core mass.
Model C
Here we examine a discrete representation of a model along the sequence whose core/envelope interface is located a .
See Also
|
Appendices: | VisTrailsEquations | VisTrailsVariables | References | Ramblings | VisTrailsImages | myphys.lsu | ADS | |